Sitemap

Know About Life

How to Replace the Oxygen Sensor in a 2001 Honda Accord

2012-05-17   Views:3

Advertisement

The oxygen sensor in your 2001 Honda Accord is responsible for reading the percent of oxygen in the spent exhaust gases coming out of the engine. The sensor then sends the information to the car's computer and the computer uses it to adjust the air/f

The oxygen sensor in your 2001 Honda Accord is responsible for reading the percent of oxygen in the spent exhaust gases coming out of the engine. The sensor then sends the information to the car's computer and the computer uses it to adjust the air/fuel mixture at the fuel injectors. Changing an O2 sensor will keep the car running smoothly, or correct idle, starting and fuel economy issues in your Accord.

Skill level:Moderately Easy

Things you need

JackJack standsOxygen sensor socketRatchet

Instructions

1 Raise the front of your Accord with a jack and position a set of jack stands under the frame rails. Lower the jack, setting the car securely on the stands, then remove the jack.

2 Locate the O2 sensor in the exhaust pipe just behind the catalytic converter. Follow the wiring harness coming off the top of the sensor up to the wiring harness connector on the car's wiring harness. Depress the locking tab and separate the two halves of the connector.

3 Position an oxygen sensor socket over the sensor, then turn it counterclockwise with a ratchet to remove it from the exhaust pipe. Discard the old sensor and thread the new one into the hole in the pipe.

4 Tighten the oxygen sensor with the oxygen sensor socket and ratchet, turning it clockwise. Route the wiring harness from the new sensor up to the connector on the car's wiring harness. Push the connector from the O2 sensor into the connector on the car until the locking tab engages.

5 Position a jack under the front end of the car and lift the car off the jack stands. Remove the jack stands from under the car, then lower the jack, carefully setting the car on the ground. Start the car and verify that it is running properly.

How to Replace the Oxygen Sensor in a 2001 Honda Accord

Category:HobbiesRelease time:2012-05-17Views:130

The oxygen sensor in your 2001 Honda Accord is responsible for reading the percent of oxygen in the spent exhaust gases coming out of the engine. The sensor then sends the information to the car's computer and the computer uses it to adjust the air/f[More]

How to Replace the Oxygen Sensor in a 2001 Jeep Cherokee

Category:HobbiesRelease time:2012-01-20Views:130

The oxygen sensor on a 2001 Jeep Cherokee mounts in the exhaust tubing and reads the oxygen level in the exhaust gases. It relays that information back to the engine computer. The computer in turn uses the information to calibrate the engine timing a[More]

How to Replace the O2 Sensor on a 2000 Honda Accord

How to Replace the O2 Sensor on a 2000 Honda Accord

Category:HobbiesRelease time:2012-12-12Views:130

The oxygen sensor in the 2000 Honda Accord--commonly called the O2 sensor-- controls the vehicle's emissions. The sensor is responsible for regulating the emissions by controlling the amount of unburned oxygen within the exhaust. When the O2 sensor f[More]

How to Replace the Dashboard Light in a 2001 Honda Accord

How to Replace the Dashboard Light in a 2001 Honda Accord

Category:HobbiesRelease time:2012-03-08Views:130

The 2001 Honda Accord has three light bulbs installed behind the dashboard. The dashboard has to be disconnected from the frame and the firewall to gain access to the rear of the dashboard. The light bulbs are in plain sight once the dashboard has be[More]

How to Replace the Oxygen Sensors on a '98 Ford Explorer Sport

Category:HobbiesRelease time:2012-05-17Views:130

Replacing the oxygen sensors, or O2 sensors, on your Ford Explorer Sport can improve its fuel economy, idle quality, and overall engine performance. The O2 sensors are responsible for reading the percentage of oxygen in the exhaust gases as the exhau[More]

How to Replace the Oxygen Sensors on a 2000 Nissan Sentra

How to Replace the Oxygen Sensors on a 2000 Nissan Sentra

Category:HobbiesRelease time:2013-08-09Views:130

The oxygen sensors monitor the oxygen saturation in your 2000 Nissian Sentra's exhaust, and the fuel-to-air ratio is regulated based on the readings from the oxygen sensors. A failing oxygen sensor can cause decreased fuel economy, and you can improv[More]

How to Replace the Oxygen Sensor on a Nissan Pathfinder

Category:HobbiesRelease time:2014-03-02Views:130

Replacing the oxygen sensors on your Nissan Pathfinder requires a special socket designed to remove and install the sensors. The oxygen sensors are a critical part of the engine management system and the car's computer depends on the reading from the[More]

How to Replace an Oxygen Sensor for a 2001 KIA Sportage

How to Replace an Oxygen Sensor for a 2001 KIA Sportage

Category:HobbiesRelease time:2014-12-02Views:130

While an oxygen sensor for a 2001 KIA Sportage keeps the engine running at greatest efficiently, a clogged oxygen sensor can cause decreased fuel economy and environmental pollutants. A sign it may be time to replace the oxygen sensor in your KIA Spo[More]

How to Replace the Oxygen Sensor on a 1994 Ford Ranger

How to Replace the Oxygen Sensor on a 1994 Ford Ranger

Category:HobbiesRelease time:2012-05-08Views:130

Oxygen (O2) sensors are a vital component for a Ford Ranger's fuel and emissions systems. This clothespin-size piece determines the current oxygen to exhaust ratio from your engine and instructs the truck's computer on how to adjust accordingly. As t[More]

How to Replace the Oxygen Sensor on an 02 Nissan Altima

How to Replace the Oxygen Sensor on an 02 Nissan Altima

Category:HobbiesRelease time:2012-09-24Views:130

A faulty oxygen sensor can rob your 2002 Nissan Altima of performance and gas mileage. If your oxygen sensor reads high it will ask your car's on-board computer to make the oxygen-fuel mixture more lean. This can cause your car to misfire, idle poorl[More]

How to Replace the Oxygen Sensor on a Toyota Sienna

How to Replace the Oxygen Sensor on a Toyota Sienna

Category:HobbiesRelease time:2013-06-04Views:130

Replacing an O2, or oxygen, sensor in your Toyota Sienna involves removal and replacement of as many as three sensors in the vehicle. The sensors are not all going to fail at once, but they will all produce the same symptoms. So before you pull any o[More]

How to Replace the Oxygen Sensor in a 1997 Saturn SL2

How to Replace the Oxygen Sensor in a 1997 Saturn SL2

Category:HobbiesRelease time:2013-07-14Views:130

The oxygen sensors in a 1997 Saturn SL2 are designed to measure the amount of oxygen in the vehicle's exhaust. A Saturn SL2 contains two oxygen sensors, one before the catalytic converter and one after the catalytic converter. Each sensor relays info[More]

How to Replace the Oxygen Sensor in an E320

Category:HobbiesRelease time:2013-12-17Views:130

When the "Service Engine Soon" light illuminates on your instrument panel, it could signal that you need to replace your oxygen sensor. Oxygen sensors are responsible for regulating the oxygen levels in your fuel. This affects your gas mileage. When[More]

How to Replace the Oxygen Sensor on a 2000 Town & Country

Category:HobbiesRelease time:2013-12-25Views:130

Proper maintenance of the oxygen sensors in your 2000 Chrysler Town and Country is crucial to managing the fuel consumption in your van. When the "Check Engine" light is on and your fuel mileage has decreased substantially, buy replacement sensors fr[More]

How to Replace the Oxygen Sensor on a 99 Chevy Cavalier

Category:HobbiesRelease time:2014-02-22Views:130

The 1999 Chevrolet Cavalier came standard with a 115-horsepower, 2.2-litre four-cylinder engine and had a 150-horsepower, 2.4-litre four-cylinder engine available in the Z24 models. Both engines utilised two emissions sensors in the exhaust system: a[More]

How to Replace the Oxygen Sensor in a Buick Regal

Category:HobbiesRelease time:2014-07-08Views:130

The oxygen sensor in your Buick Regal can fail. It must be replaced right away in order for you vehicle to run properly. The oxygen sensor helps regulate the oxygen and fuel ratio. It senses when more or less oxygen needs to be added to the fuel as i[More]

How to replace the oxygen sensor in a buick rendezvous

How to replace the oxygen sensor in a buick rendezvous

Category:HomeRelease time:2014-07-31Views:130

Trying to replace the oxygen (O2) sensor in your Buick Rendezvous is not a difficult task, as long as you approach the job with the correct strategy. Oxygen sensors work mounted on the exhaust system, under high temperatures. This causes them to tend[More]

How to Replace the Oxygen Sensor on a 1999 Saturn SL

How to Replace the Oxygen Sensor on a 1999 Saturn SL

Category:HobbiesRelease time:2014-08-05Views:130

The 1999 Saturn SL features a four-cylinder, 1.9-litre engine with two oxygen sensors that monitor the exhaust emissions. One is located directly into the manifold and can be accessed and replaced from the engine compartment. The other is located jus[More]

How to Replace the Oxygen Sensor on a 2000 Silverado

How to Replace the Oxygen Sensor on a 2000 Silverado

Category:HobbiesRelease time:2014-10-16Views:130

The oxygen sensors in your 2000 Chevy Silverado inform the drivetrain computer of the oxygen content in the exhaust stream. This information helps the computer better adjust the air/fuel mixture sent into the engine's combustion chambers. The oxygen[More]

How to Replace the Oxygen Sensor on a 2003 Ford Expedition

Category:HobbiesRelease time:2012-11-02Views:130

The 2003 Ford Expedition uses two oxygen sensors, one mounted in each exhaust pipe behind the catalytic converters, to monitor the amount of oxygen in the exhaust gas. Oxygen in the exhaust causes the sensors to send an electrical signal to the on-bo[More]

Hot
PWC stands, or powered water craft stands, hold water crafts such as jet skis and water scooters. The idea is that when they are not on the trailer on the way to the lake, you can place them on this type of stand to move around easily while in storag [More]
Connecting a moustache to a beard can be challenging, due to the fact that every person is born with a different genetic make-up. Where others seem to excel in beard growing, you may be left to shave patchy facial hair. The hardest thing about growin [More]
Cab-over truck campers are one of the smallest types of campers available. These campers slide into the bed of a truck and curve over the cab. Amenities in the camper can include a bed, shower, tub, toilet, stove, refrigerator and table. When fully e [More]
The Nokia 6600 slide phone's battery comes preinstalled and precharged, but you may need to remove it down the road if you need to replace it with a new one. Another reason you'd need to remove the battery is to access the Nokia 6600's memory card, o [More]
Wood floor maintenance is typically simple. From time to time, the clear coat of wax on top of your floor may need a little face lift. To do this properly, rent a slow-speed floor buffer from a tool rental company for a day. Two or three standard siz [More]
Hydraulic systems are like boxing; simple in concept, complex in execution. A braking system works by transferring the mechanical motion of your foot into hydraulic pressure and then back into mechanical movement at the brake caliper. But if you're w [More]
Sump pumps are used in basements, crawl spaces and other areas where unwanted water tends to gather. These pumps are activated when the water in the sump basin reaches a preset depth. The water is then pumped out of the basin and away from the home. [More]
Dancing can be a wonderful way for kids to have fun while getting some great exercise and also enjoying music in the loving company of their friends. Unlike sports, which artificially train children to be unnaturally competitive with each other, danc [More]
There are a number of ways to recycle and dispose of wood ash. Before attempting any of these methods, make sure the ash from your fire is cold and can be safely handled. Skill level:Moderately Easy Instructions 1 Spread ashes on suitable areas of th [More]
Mounting a fish requires the taxidermist to skin the fish, preserve and mount the skin, and then airbrush the colours back onto the dried skin. Prior to bringing a fish to a taxidermist, care must be taken to protect the skin from damage, as the bett [More]